088 - Router Table Fence (for tablesaw router wings)

Plans available at my website http://thewoodknight.com/downloads/ro...


---

Follow me on
Twitter https://twitter.com/vikingcode
Facebook https://www.facebook.com/TheWoodKnight
Website http://thewoodknight.com/
Instagram https://instagram.com/thewoodknight/

Support me and free woodworking content at
https://www.patreon.com/thewoodknight

---
Music

Music by Sophonic Media http://instrumentalsfree.com

See more here: https://www.youtube.com/watch?v=dxgxlgSj3js

Would like to know the best ways to make use of a frouter table fence? Below are ideas to obtain the most from your router table.

Usually, you move your work along the fencing. If making use of a miter channel, then the fence needs to be square to the miter channel.

You can make modification in profile as well as depth of cut. A Router Lift makes this very easy.

A quality frouter table fence fencing alleviates dirt collection. Use your Router Table and also Fencing for simpleness and also relieve!

You ought to never place your work between the router and the fence bit. That is just throwing down the gauntlet.

Normally, you slide the timber from right to left (when considering the fencing from the front). That is an anti-climb cut. You make nearly all cuts this way.

You could go a brief distance in the other direction if very cautious. You must hold on limited to avoid kickback and/or injury. This climb cut offers cleaner edges, however you must only try it after a lot of experience.

Only do less than 15% of your job in this manner. You should just utilize light or superficial cuts. Do NOT take large cuts. Only do it when you hands are shielded and also away from the router little bit.

Ways to use a Router Table to center edge-to-edge joints:

Have you ever asked yourself how to center edge-to-edge joints? You use this technique for making solid table tops, wide panels, or even make bordering to walk around your router table top.

Let's make use of a real instance of oak edging on a MDF Router Table Top. The top is 1 1/8" thick. The oak edging is 1 1/8" thick.

How do we ensure a focused edge?

Select the tongue dimension. You have a 1/4" port cutter. You want the tongue thickness less than 2 times the cut. The tongue density is a little less compared to 1/2". We use a 1/4" depth of cut for this instance.
We want a tongue that is less than 1/2" in thickness. We know that the rabbet on the Table Top is slightly more than 5/16" on both sides of a 1 1/8" thick item.
Rabbet the leading with a rabbet bit with a birthing to create a 1/4" rabbet. You do not wish to take a lot throughout your very first pass. The depth of cut is set for 1/8" for your very first pass.
Set the fence so it is despite having the bearing of the rabbet little bit.
Make sure the workpiece is flat on the Router Table Top. Or make use of the router on top of the work surface.
A router lift makes this simple. Keep in mind: you rout both sides; for that reason utilize half the change for each side.
Make your change, rout the top as well as bottom again. The tongue's thickness is currently somewhat less than 1/2".
Change your rabbeting bit with your 1/4" slot cutter. I always detach the source of power to the router before altering bits!
Sit the rabbeted item on the router table top near the slot cutter. Raise the Router so all-time low of the slot cutter aligns with the bottom of the tongue. If the work surface is big, you may need support.
Set the depth of cut for the port to around 3/16". Test the slot on the tongue. By the method, the Concierge Cord 7518 Router makes this a snap.
Considering that the port cut is 1/4", the second pass is not making use of the entire cutter. You get a precisely center slot that fits on the tongue.
When the port (groove) fits on the tongue, you are ready to establish your final deepness of the groove. The final depth of cut is somewhat more than 1/4" to allow for adhesive.
Establish your fence for this last depth. Remember - make two passes with the slotter. This offers you an exact fit.
You can use this technique for any type of edge-to-edge joinery, such as tabletops, panels, large drawer fronts, and whenever you wish to sign up with two-pieces. You obtain excellent placement and also a well-founded joint.


Let's use an actual example of oak bordering on a MDF Router Table Top. Make sure the workpiece is level on the Router Table Top. Or utilize the router on top of the work surface.
Rest the rabbeted piece on the router table top near the port cutter. Raise the Router so the base of the port cutter straightens with the base of the tongue.
Plans available at my website http://thewoodknight.com/downloads/ro...---Follow me on Twitter https://twitter.com/vikingcodeFacebook https://www.facebook.com/TheWoodKnightWebsite http://thewoodknight.com/Instagram https://instagram.com/thewoodknight/Support me and free woodworking content at https://www.patreon.com/thewoodknight---MusicMusic by Sophonic Media http://instrumentalsfree.comSee more here: https://www.youtube.com/watch?v=dxgxlgSj3jsWould like to know the best ways to make use of a frouter table fence? Below are ideas to obtain the most from your router table.Usually, you move your work along the fencing. If making use of a miter channel, then the fence needs to be square to the miter channel.You can make modification in profile as well as depth of cut. A Router Lift makes this very easy.A quality frouter table fence fencing alleviates dirt collection. Use your Router Table and also Fencing for simpleness and also relieve!You ought to never place your work between the router and the fence bit. That is just throwing down the gauntlet.Normally, you slide the timber from right to left (when considering the fencing from the front). That is an anti-climb cut. You make nearly all cuts this way.You could go a brief distance in the other direction if very cautious. You must hold on limited to avoid kickback and/or injury. This climb cut offers cleaner edges, however you must only try it after a lot of experience.Only do less than 15% of your job in this manner. You should just utilize light or superficial cuts. Do NOT take large cuts. Only do it when you hands are shielded and also away from the router little bit.Ways to use a Router Table to center edge-to-edge joints:Have you ever asked yourself how to center edge-to-edge joints? You use this technique for making solid table tops, wide panels, or even make bordering to walk around your router table top.Let's make use of a real instance of oak edging on a MDF Router Table Top. The top is 1 1/8" thick. The oak edging is 1 1/8" thick.How do we ensure a focused edge?Select the tongue dimension. You have a 1/4...