How to make a patio table. This outdoor table is easy to build!

What's yellow and black and green and yellow all over? Microjig, maker of the GRR-RIPPER. Work safer, work smarter. The first thing I need to do is cut these two, 10' long boards down to manageable lengths. By ripping all the boards to 7" wide, I'm also squaring off the rounded edges. Since the tabletop starts out as an octagon, I need to cut all the miters to 22.5 degrees. I'm cutting

these on my miter saw, then I'll try to get more accurate miters on my tablesaw. I think I'll be able to get much more accurate cuts using this brand new miter gauge a viewer sent me. It looks like they are going to fit together really nicely. Now I need to cut a rabbet on the inside edge of each board. I'll join the octagon together using pocket screws. I'm going

to glue and screw these all together. These are 1x4s that I'm ripping down to 3" wide. I'm going to screw all these boards in from underneath, no glue. I'm going to start with the center board and work my way to the sides, cutting each board to size. I clamped the board in place along that rabbet and that should hold it so I can put the screws in.   I

can slide it over and do the same on this side. The rest of them, I'm going to space using the quarter inch piece of plywood. PRO TIP! I discovered it's important to drill a pilot hole in the ¾" board or it will split. This board is going to need its corner cut off, and that is a 45 degree angle. After a lot of trimming and testing and testing and

trimming, I finally got it to fit, just right. All the edge boards are a little easier, they have 45 degree angles on both sides. I spent a lot of time sanding this to level out any of the uneven surfaces. I'll probably still come back to it and do some finer sanding once it's all assembled. Here I'm finding the center point and drawing a circle. I'm building the entire base and

legs out of 2x4s. I'm cutting all the pieces to their exact dimensions using my tablesaw. I'm going to join all the center pieces together using half-lap joints. And all that means is I'm going to cut out a large notch, half the thickness of the wood in each piece. I can make sure it's centered by flipping the board end-to-end and  using only one stop block as a reference. Those two

notches just interlock. Without changing my blades, I can cut rabbets on the ends of the top boards. I'll start the assembly by glueing these cross pieces together. And I'm also putting some screws in. I just don't want to put any screws in the middle where I need to drill a hole for the umbrella. To assemble the base, I'm going to start by attaching the legs to the lower

cross brace. I decided this needed some clamping pressure also, to help draw these joints together. This cross brace drops down into these rabbets. These 1 ½" diameter holes are for the umbrella. The idea here is that the tabletop will rest...

See more here: https://www.youtube.com/watch?v=DPIfzyXd9Hg

Woodworking can be a great pastime for individuals from all walks of life. Whether you are a professional, or are just beginning, there is always something new for you to find out about the woodworking skill. If you like to find out more about this pastime you must check out the short article that follows below for some fantastic guidance.

Ensure your workspace is safe, well-lit and arranged. Working with woods is tough work, and it is dangerous work when your workspace is dim and there are safety threats in the area. Make certain there are no spills, tripping risks and other security threats that are a catastrophe waiting to occur.

Prior to practicing innovative woodworking strategies, make sure you have actually got the basics down. Begin slow, and work up from there.

If you are trying brand-new skills, make certain that you practice on some wood that has no value, like some scraps. You do not wish to lose an expensive piece of wood prior to you know exactly what you are doing. As soon as you have actually mastered your new skills, you can relocate to a much better piece of wood.

Benefit from several tools instead of aiming to do all your work on simply one. A jig, a tablesaw, a bandsaw and a lathe all have their own uses. It is important that you know what each of these tools do and you use them appropriately while getting the job done.

Check to make sure it is within the guidelines if you are going to be doing a big woodworking project on the outside of your house. Your local government might have zoning guidelines or even a permit process needed for structures like garages, decks as well as storage sheds. Also talk to your neighborhood watch if there is one.

Make sure you buy the right tool for the job. A circular saw is electric; however, a hand saw is not.

You may delight in consuming a beer while you are doing woodworking. Nevertheless, working with a saw and drinking is a dreadful combination. When working with power tools, consuming alcohol can trigger major injuries. This rule applies to any drug that might impact your ability to believe plainly, whether legal or not.

Exactly what this suggests is to not get lost in chasing after perfectionism or analysis paralysis. Be proud of what you are able to do with woodworking, and do exactly what you can to discover particular skills that improve on exactly what you already have mastered.

As you check out at the start of this article, there is so much that you can discover woodworking that you will never ever know whatever. Even though that is a fact, there is no factor to not attempt. Now that you read this post you understand a bit more, and continuing to find out will only lead you to being a better woodworker.


Make sure your work area is safe, well-lit and organized. Working with woods is hard work, and it is hazardous work when your work area is dim and there are safety risks in the area. Take advantage of a number of tools instead of trying to do all of your work on simply one. Working with a saw and drinking is a terrible mix. Consuming alcohol can cause serious injuries when working with power tools.
What's yellow and black and green and yellow all over? Microjig, maker of the GRR-RIPPER. Work safer, work smarter. The first thing I need to do is cut these two, 10' long boards down to manageable lengths. By ripping all the boards to 7" wide, I'm also squaring off the rounded edges. Since the tabletop starts out as an octagon, I need to cut all the mi...