How to Sharpen Woodturning Tools on a Bench Grinder

At Craft Supplies USA, We believe that properly ground sharp tools are fundamental to successful and enjoyable woodturning. Getting consistent, repeatable results when you sharpen, doesn't need to be expensive or complicated. In this short video, you'll learn the same basic sharpening techniques as taught by top professionals in our woodturning workshop program for over 30 years. Using a standard 8" bench grinder, wolverine sharpening system and a few raptor

set up tools, you too can create perfectly ground, razor sharp tools with consistent results, following these simple steps. And remember... Always use eye protection and keep your wheels properly dressed. When it comes to bowl gouges, we recommend a 50º single bevel grind, as it provides maximum control, while allowing you to turn a wide variety of bowls using a single tool. To sharpen, place the bowl gouge in the Vari-Grind

Jig. Using the 2" Raptor Grinding Jig, set the tool position and tighten. Position the tool support slide using the 50º Raptor Setup Tool. Tighten and you're ready to go! Using light pressure, sharpen the tool using a smooth, side-to-side motion, making sure not to pause along the way. This ensures a smooth transition along the cutting edge. Carefully shape the tool as shown, while trying to avoid bluing the cutting edge in the

process. When your'e done, you should have a single faceted bevel and cutting edge that looks like this. Spindle gouges offer maximum versatillty when ground with a 45º single bevel. To sharpen, place the spindle gouge in the Vari-Grind Jig. Using the 2" Raptor Grinding Jig, set the tool position and tighten. Position the tool support slide using the 45º Raptor Setup Tool. Tighten and you're ready to go! Using light pressure, sharpen

the tool using a smooth side-side motion, making sure not to pause along the way. This ensures a smooth transition along the cutting edge. Carefully shape the tool as shown, while trying to avoid bluing the cutting edge in the process. When you're done, you should have a single faceted bevel and cutting edge that looks like this! Few tools make the chips fly like a spindle roughing gouge. To sharpen,

set the tool support platform to 35º using the Raptor Setup Tool. Place the tool flat on the rest. Using light pressure, sharpen the tool using a smooth side-to-side rocking action, while avoiding bluing the cutting edge in the process. When properly ground, your spindle roughing gouge should have a squared end and look like this. There's no substitute for a well ground scraper, when it comes to removing imperfections and

creating a smooth surface. The bevel angle on a scraper should be slightly under a 90º angle. A blunt bevel angle helps to support the cutting edge, and makes it less aggressive too. To sharpen, place the scraper on the platform and tilt the platform slightly downward to set the bevel angle. Using a sweeping side-to-side motion, shape the end of the scraper as desired. The cutting edge is ready when

it's shaped the way you want and you can feel a burr edge on the top side of the tool. The length of the bevel on a skew chisel should be 1/1.5x the thickness of the blade. Generally speaking, a...

See more here: https://www.youtube.com/watch?v=j__h45sQErg

Woodworking: What You Must Understand about Working With Woods

Woodworking is an ability that has actually been valued because the start of time. Many woodworkers enjoy it from a creative viewpoint while others delight in producing larger, more practical products. Whatever it is that you take pleasure in about woodworking, here are some tips to help you enjoy it even more.

Usage stop obstructs to your benefit for more precise work. When cutting a lot of pieces the very same size, no matter how carefully you determine, you often discover little variations. Use a pre-cut stop block to make those measurements determine accurate. Then the table saw will stop at simply the right length length.

Put in the time to plan your woodworking project detailed prior to you even start. Doing this will assist to ensure that you are getting the outcomes that you are trying to find. , if you do not prepare ahead it is likely that you will make an error that might destroy the entire job.

.

If you have actually been doing woodworking for some time now you might wish to think about using your skills to make your very own furnishings. If you currently have all that you require you could even do this as a service to those that are less lucky than you. It is a fantastic method to share your passion with others.

Use tin snips to trim laminate for your tasks. These let you cut laminate into a size you can utilize. You need to purchase tin snips that you will use specifically for cutting laminate to make sure they remain sharp.

Make the most of a number of tools instead of aiming to do all of your deal with just one. A jig, a tablesaw, a bandsaw and a lathe all have their own usages. It is important that you understand exactly what each of these tools do and you use them accordingly while finishing the job.

A lot of store owners have a variety of sockets that can be utilized for a range of radii. You will get an ideal arc each time using this strategy.

If you're trying to find that very first woodworking task, how about starting with an easy box? That's most likely the most popular very first woodworking project out there. Buy some low-cost wood that you like, and design a box that could work around your home. Maybe it's for composing utensils, or possibly it's for the cooking area? There are a great deal of choices.

Prior to even starting a woodworking project, make sure you have a sufficient and correct location to work in. You certainly don't desire your home filled with sawdust. Some woodworking supplies, such as stains, varnish and paint strippers, have noxious fumes. Preferably, you will have a separated garage or a shed to work in considering that an outdoors space is a perfect location.

As you already know, woodworking can be a creative and very beneficial hobby. There is a lot of creativity and satisfaction that goes into developing products of wood. Ideally the suggestions from above will boost your woodworking efforts and motivate you to make a lot more masterpieces to take pleasure in.


Usage stop blocks to your benefit for more accurate work. Utilize a pre-cut stop block to make those measurements determine accurate. If you have actually been doing woodworking for some time now you might want to think about utilizing your abilities to make your own furniture. Usage tin snips to cut laminate for your projects. You need to purchase tin snips that you will utilize specifically for cutting laminate to make sure they remain sharp.
At Craft Supplies USA, We believe that properly ground sharp tools are fundamental to successful and enjoyable woodturning. Getting consistent, repeatable results when you sharpen, doesn't need to be expensive or complicated. In this short video, you'll learn the same basic sharpening techniques as taught by top professionals in our woodturning workshop program for over 30 years. Using a standard 8" ben...