How To Stain Pine To Look Like Brazilian Cherry

Todd from http://www.homeconstructionimprovemen... shares tips on how stains pine or pine plywood to look like Brazilian Cherry or Mahogany.

See more here: https://www.youtube.com/watch?v=K1SNJTI9X-4

Todd from http://www.homeconstructionimprovemen... shares tips on how stains pine or pine plywood to look like Brazilian Cherry or Mahogany.

See more here: https://www.youtube.com/watch?v=K1SNJTI9X-4

If you have to finish a trim or furnishings item constructed from want, and you're attempting to stain the wood dark, you might encounter problems getting the rich, dark tone that you would certainly such as.

As well as if you obtain the deep, dark discolor shade you wanted, why are your results looking so "blotchy?".

To tarnish yearn wood dark, each time, follow these actions.

Beginning with fining sand.

Points initially, with any staining task, give the wood a good sanding. Pine wood is a softwood, and if you use a power sander, you'll frequently wind up with some obvious scratches once you use stain to the timber.

To ensure a dark coating, use a medium grit sanding sponge or the comparable sandpaper, which is about 100-grit. If you've got a strictly flat surface area, cover a little square piece of sandpaper around a sanding block (an easy block of timber will do) as well as sand with the grain, yet at a minor angle.

Why at a small angle? staining pine grain is defined by the light, softer "earlywood" as well as darker, harder "latewood." By not crossing the grain just a little, you are mosting likely to sand down much more earlywood compared to latewood as well as wind up with a fairly bumpy surface, instead of the entirely flat surface area you're aiming to achieve.

Do not sand with a grit any kind of finer than tool or 100-grit if you're after a darker coating. Sanding with this a little harsh grit assists to open the pores of the want wood, which will certainly approve a lot more stain. Just what you don't want to do is use a fine sanding sponge or 180-grit (or greater) sandpaper. This properly closes and polishes the wood off the wood pores, making it harder to stain the yearn dark.

Eliminate blotchy finished pineAfter an extensive sand work, vacuum the job and afterwards make use of a tag dustcloth to wipe up all of the staying dirt particles.

Completed ache can look blotchy because of the various growth cycles of the timber (and is also dependent on exactly how the final item was cut.) To eliminate this unsightly problem, get a canister of pre-stain timber conditioner at your regional home facility or paint shop. The timber conditioner ensures a much more consistent stain shade by closing off several of the bigger pores as well as minimizing tarnish absorption in those areas.

Nonetheless, making use of the staining pine helps make it tougher to discolor want dark. Nevertheless, so long as you're dealing with a dark oil-based permeating tarnish, you could obtain the dark color you would such as.

Follow the directions on the could for the timber conditioner. Enabling the timber conditioner to completely dry entirely will entirely block the wood pores and it will certainly be hard to attain the dark shade you're looking for.

Start discoloration.

Just how you obtain the discolor on the timber is trivial. You could utilize a foam brush, routine brush, or tidy fabric. Apply generously. Try not to get drips, however. To make sure a nice dark finish, wait as long as the producer enables before wiping off the excess tarnish. See to it you don't wait too long though, or else the discolor will certainly obtain ugly and also difficult to wipe off.


Pine timber is a softwood, as well as if you use a power sander, you'll usually wind up with some visible scrapes once you apply discolor to the wood. Sanding with this somewhat rough grit helps to open up the pores of the yearn timber, which will certainly approve more tarnish. The wood conditioner ensures a more consistent tarnish color by closing off some of the larger pores and lowering tarnish absorption in those locations.

Permitting the timber conditioner to dry completely will totally obstruct the timber pores and also it will be difficult to attain the dark shade you're looking for.

How you obtain the tarnish on the wood is not crucial.
Todd from http://www.homeconstructionimprovemen... shares tips on how stains pine or pine plywood to look like Brazilian Cherry or Mahogany.See more here: https://www.youtube.com/watch?v=K1SNJTI9X-4Todd from http://www.homeconstructionimprovemen... shares tips on how stains pine or pine plywood to look like Brazilian Cherry or Mahogany.See more here: https://www.youtube.com/watch?v=K1SNJTI9X-4If you have to finish a trim or furnishings item constructed from want, and you're attempting to stain the wood dark, you might encounter problems getting the rich, dark tone that you would certainly such as.As well as if you obtain the deep, dark discolor shade you wanted, why are your results looking so "blotchy?".To tarnish yearn wood dark, each time, follow these actions.Beginning with fining sand.Points initially, with any staining task, give the wood a good sanding. Pine wood is a softwood, and if you use a power sander, you'll frequently wind up with some obvious scratches once you use stain to the timber.To ensure a dark coating, use a medium grit sanding sponge or the comparable sandpaper, which is about 100-grit. If you've got a strictly flat surface area, cover a little square piece of sandpaper around a sanding block (an easy block of timber will do) as well as sand with the grain, yet at a minor angle.Why at a small angle? staining pine grain is defined by the light, softer "earlywood" as well as darker, harder "latewood." By not crossing the grain just a little, you are mosting likely to sand...