Woodturning with Wagner Texturing Tools

My name is Joe Wagner I've been woodturning for quite a few years and every year at Christmas time I make ornaments for my grandchildren and as gifts for my wife to give away and this is the one that I did last Christmas the texture on the side of the cap is what I was trying to trying to accomplish and I tried other texturing tools and

I was wasn't pleased with them so what I did is I went out and found the parts and pieces to make these type of tools it's a knurl and there will be three different sizes available the quarter wheel is 12 teeth per inch this is a finer 16 teeth per inch and the narrow one is 16 teeth per inch also the pattern all depends what you like to

put on, if you like a deeper pattern is the one you want to go with. A little bit finer pattern use something like this the main thing you want to know, you'll want to do when you get your tool is oil it on the side, with just some light machine oil and that way it prevents any friction, it is a close tolerance it's a hardened pin with a

hardened knurl, a hardened texting tool and it will prolong the life of the cutter in the tool as well ok when you get ready to do the knurling or the texturing you have to have your toolrest down low so that when you set the tool on it will be at center, the center of the wheel, and it needs to be in line with the center of the piece speed;

you want to keep it down to about four or five hundred rpm you come in here and you line it up. It has to be pretty much a square approach, a straight on approach, for the first bite you run it in and what it gives you is the pattern if it's not deep enough for you you go back in. You see the lines and set the cutter back

on let it float for a second, it'll pick back up it'll give you a pattern a little bit deeper, a little more detailed. As you come around here again you let it float into your pattern - you can see there's about four lines. Let one of the teeth, or several of the teeth, pick up the pattern like so now you have to lean fairly hard because you're not

cutting wood you're just denting the wood - putting an indentation in the wood your pattern will go right on around the same way let it pick up the pattern, you can use it around Your pattern carries on. At this point in my own shop I would quit, reverse the piece finish turning the top down to the dimensions I'm looking for and then finish knurling up to the shoulder

See more here: https://www.youtube.com/watch?v=PXFTPWupA30

Woodworking: What You Should Learn about Dealing With Woods

Woodworking is an ability that has actually been valued because the beginning of time. Numerous woodworkers enjoy it from an artistic viewpoint while others delight in producing bigger, more functional products. Whatever it is that you enjoy about woodworking, here are some suggestions to help you enjoy it even more.

Use stop blocks to your advantage for more precise work. Utilize a pre-cut stop block to make those measurements determine precise.

Take the time to plan out your woodworking project step-by-step prior to you even begin. Doing this will assist to guarantee that you are getting the outcomes that you are trying to find. If you do not plan ahead it is likely that you will make a mistake that might mess up the entire project.

, if you have actually been doing woodworking for some time now you may desire to believe about utilizing your abilities to make your own furnishings.. If you already have all that you need you could even do this as a service to those that are less lucky than you. It is a great way to share your enthusiasm with others.

Usage tin snips to trim laminate for your jobs. These let you cut laminate into a size you can use. You should purchase tin snips that you will use particularly for cutting laminate to make sure they stay sharp.

Make the most of numerous tools instead of aiming to do all of your deal with just one. A jig, a tablesaw, a bandsaw and a lathe all have their own usages. It is important that you understand exactly what each of these tools do and you utilize them appropriately while getting the job done.

A lot of shop owners have a range of sockets that can be utilized for a range of radii. You will get an ideal arc each time utilizing this method.

If you're looking for that first woodworking job, how about beginning with a basic box? That's probably the most popular first woodworking task out there. Buy some inexpensive wood that you like, and create a box that could work around your house. Maybe it's for writing utensils, or perhaps it's for the cooking area? There are a lot of options.

Before even starting a woodworking project, make certain you have a appropriate and proper location to work in. You absolutely don't want your living space filled with sawdust. Some woodworking materials, such as stains, varnish and paint strippers, have toxic fumes. Preferably, you will have a removed garage or a shed to operate in because an outdoors space is an ideal location.

As you currently understand, woodworking can be a really helpful and creative pastime. There is a lot of imagination and pleasure that goes into producing items of wood. Hopefully the tips from above will enhance your woodworking efforts and influence you to make much more masterpieces to delight in.


Use stop blocks to your benefit for more precise work. Utilize a pre-cut stop block to make those measurements determine accurate. If you have actually been doing woodworking for some time now you may want to think about using your skills to make your own furnishings. Use tin snips to trim laminate for your jobs. You should purchase tin snips that you will use particularly for cutting laminate to make sure they stay sharp.
My name is Joe Wagner I've been woodturning for quite a few years and every year at Christmas time I make ornaments for my grandchildren and as gifts for my wife to give away and this is the one that I did last Christmas the texture on the side of the cap is what I was trying to trying to accomplish and I tried other texturi...